Optimization of three-dimensional boiling enhancement structure at evaporation surface for high power light emitting diode

A theoretical model of phase change heat sink was established in terms of thermal resistance network. The influence of different parameters on the thermal resistance was analyzed and the crucial impact factors were determined. Subsequently, the forming methods including ploughing–extrusion and stamping method of boiling enhancement structure at evaporation surface were investigated, upon which three-dimensional microgroove structure was fabricated to improve the efficiency of evaporation. Moreover, the crucial parameters related to the fabrication of miniaturized phase change heat sink were optimized. The heat transfer performance of the heat sink was tested. Results show that the developed phase change heat sink has excellent heat transfer performance and is suitable for high power LED applications.     

极端耗水层带精准识别和调堵新技术

油田注水开发后期,部分油层存在极端耗水层带,存在耗水量大,注水驱油效率低,水循环成本高的开发问题,精准认识并有效封堵极端耗水层带,可提高注水利用率。目前国外出现了应用磁性纳米粒子的精细表征新技术及超顺磁性纳米颗粒封堵新技术,抑制极端耗水,实现低成本、高强度、深度堵调。     

Compiler compatible 5.66 Mb/mm2 8T 1R1W register file in 14 nm FinFET technology

1-read/1-write (1R1W) register file (RF) is a popular memory configuration in modern feature rich SoCs requiring significant amount of embedded memory. A memory compiler is constructed using the 8T RF bitcell spanning a range of instances from 32 b to 72 Kb. An 8T low-leakage bitcell of 0.106 μm² is used in a 14 nm FinFET technology with a 70 nm contacted gate pitch for high-density (HD) two-port (TP) RF memory compiler which achieves 5.66 Mb/mm² array density for a 72 Kb array which is the highest reported density in 14 nm FinFET technology. The density improvement is achieved by using techniques such as leaf-cell optimization (eliminating transistors), better architectural planning, top level connectivity through leaf-cell abutment and minimizing the number of unique leaf-cells. These techniques are fully compatible with memory compiler usage over the required span. Leakage power is minimized by using power-switches without degrading the density mentioned above. Self-induced supply voltage collapse technique is applied for write and a four stack static keeper is used for read Vmin improvement. Fabricated test chips using 14 nm process have demonstrated 2.33 GHz performance at 1.1 V/25 °C operation. Overall V_min of 550 mV is achieved with this design at 25 °C. The inbuilt power-switch improves leakage power by 12x in simulation. Approximately 8% die area of a leading 14 nm SoC in commercialization is occupied by these compiled RF instances.     

高泉背斜地层压力测井多参数综合解释与异常高压成因

目前国内外地层压力测井解释方法较多,但大多数方法基于欠压实沉积理论并局限于单一的地层岩性,尤其是针对盆地边缘山前深层构造,单一测井参数确定地层压力误差较大,且无法解释沉积压实机制以外的异常高压。为此,将多种异常高压机制相关的测井参数进行综合解释,建立适合山前复杂构造的地层压力测井多参数计算模型,评价准噶尔盆地南缘高泉背斜高探1井的地层压力剖面,其计算结果与钻井实测数据吻合,相对误差小于3.00%.同时,基于原始沉积加载—卸载过程力学原理,利用地层压力测井多参数分析判别出高泉背斜深层各层系异常高压的形成机制。     

高地压严重突出区域下向穿层钻孔预抽消突技术

利用工作面高抽巷施工掩护顺槽掘进工作面下向穿层条带预抽钻孔,通过对钻场底板深、浅孔注浆封堵围岩裂隙解决了孔内返水不畅难题;采取了"两堵一注"封孔方式确保封孔严密不漏气;孔内全程下吹水管,实现了单孔、分组、定时吹水工作目标,提高了下向消突钻孔抽采效果,形成了一套高效、快速的下向穿层钻孔消突管理模式,实现了高地压严重突出区域煤层高效消突以及技术经济一体化目标,安全经济效益显著。     

高含硫气田集输系统增压模式优化研究

随着高含硫气田的持续开发,气井井口压力逐步低于集输压力,亟需实施集输系统增压运行。采用OLGA软件,以气液两相流、压降预测、耦合传热理论为基础,针对高含硫气田集输管网高程差、气体组分、液气比、管网全尺寸参数等工况条件,建立了复杂山地高含硫湿气集输系统生产运行的数值模型,以集输系统生产历史数据为基础,验证模型准确性并进行修正。考虑单井、多井或单线配置压缩机等情况,根据开发预测的各井压力变化情况,计算集输管网的压力分布及系统能耗,重点分析了单站增压、区域+单站增压、集输干线增压三种模式,最终优选出高含硫气田集输系统增压模式。     

一种军棋机器博弈的多棋子协同博弈方法

针对在军棋博弈不完全信息对弈中，面对棋子不同价值、不同位置、不同搭配所产生的不同棋力，传统的单子意图搜索算法，不能满足棋子之间的协同性与沟通性，同时也缺乏对敌方的引诱与欺骗等高级对抗能力。本文提出一种结合UCT搜索策略的高价值棋子博弈方法，实现高价值棋子协同博弈的策略。实战经验表明:高价值多棋子军棋协同博弈策略优于单棋子军棋博弈策略。     

冷轧退火对FeMnCoCrAl高熵合金组织和力学性能的影响

使用真空电弧炉熔炼出(Fe₅₀Mn₃₀Co₁₀Cr₁₀)₉₄Al₆合金,利用冷轧及在不同温度对合金进行退火,以期望得到由多尺度再结晶晶粒构成的层状结构;并对不同退火温度的样品进行拉伸性能测试。利用扫描电镜和EBSD对合金组织形貌进行表征,采用X射线衍射方法研究其相组成。结果表明:合金在铸态和冷轧后相组成未发生变化,700 ℃退火得到较好的多尺度再结晶晶粒的层状结构,其屈服强度为487 MPa,抗拉强度为708 MPa,断后伸长率为39%,表现出良好的综合力学性能。     

珲春地区高瓦斯矿井煤自然发火标志气体研究

为了探究珲春地区高瓦斯矿井煤自然发火情况，选取该地区板石煤矿22、23a和八连城煤矿18#、26#共4个煤层进行程序升温特性实验，分析了CO及烃类气体产生量随温度的变化规律，优选自然发火标志气体，测算煤自燃临界温度。结果表明，板石22、23a和八连城18#、26#四个煤层的自燃临界温度分别为101.0℃、97.6℃、121.0℃、169.1℃。CO和C2H4的初现温度大约在30℃与80～120℃，且产生量随温度单调递增，可作为煤自燃预测预报的主要参考指标|而同时，为了保证检测的全面与准确，还可以将规律性良好的其他烃类气体、烯烷比和链烷比进行辅助参考。